Never Ending Security

It starts all here

How to Get Started With pfSense as a FreeBSD Router


pfSense is a free, open source customized distribution of FreeBSD tailored for use as a firewall and router. In addition to being a powerful, flexible firewalling and routing platform, it includes a long list of related features and a package system allowing further expandability without adding bloat and potential security vulnerabilities to the base distribution. pfSense is a popular project with more than 1 million downloads since its inception, and proven in countless installations ranging from small home networks protecting a PC and an Xbox to large corporations, universities and other organizations protecting thousands of network devices.

This project started in 2004 as a fork of the m0n0wall project, but focused towards full PC installations rather than the embedded hardware focus of m0n0wall. System also offers an embedded image for Compact Flash based installations, however it is not our primary focus.

Click here for details

It is supported by the open source community under the General Public License (GPL) which makes it Free to all to use. As with many LINUX distribution, The minimum hardware requirements to use pfSense is a computer with the following:

  • CPU – 100 MHz Pentium
  • RAM – 128 MB
  • CD-ROM for initial installation
  • 1 GB hard drive
  • Two Network Interface Cards

Basic Install and Setup
Get p fSense
Download the latest version


Boot your chosen PC with the CD. You will be present with the following “Welcome” screen.
For our basic install, you can press [Enter] for the default option.



If you can see the “Configure Console” screen, chances are there aren’t any changes you need to make to the console. Press the Down arrow on your keyboard to highlight the “<Accept these Setting>” option and press [Enter]


On the “Select Task” window, select the “<Quick/Easy Install>” and press [Enter].


At the “Are you SURE?” screen, confirm your decision to install by highlighting the “< OK >”  option and pressing [Enter].
Any data currently on the first hard drive of the system will be destroyed !


It can take up to 10 minutes for install to finish, depending on your hardware.
installer is formatting your drive and copying the software to your system.


At the “Install Kernel(s)” screen, ensure

“< Symmetric multiprocessing kernel (more than one processor) >” is highlighted and press [Enter].


At the “Reboot” screen, remove the CD and ensure that “< Reboot >” is highlighted and press [Enter].


After the system reboots, you will be presented with the initial “Welcome” menu.
Press [Enter] to select the default


During the boot phase, compatible network interface cards will be displayed.


Since this is a basic setup, we will not want to configure “VLAN”
Type “n” and press [Enter]


From the list of valid interfaces, type the name of the network interface card
that will be connected directly to the Internet (cable modem, dsl, etc)


From the list of valid interfaces, type the name of the network interface card that will be connected to your internal network. This will serve as your “LAN” interface. Repeat this step for each additional network interface card listed as a valid interface  Once you are finished, press the [Enter] to select nothing and move to the next step of the setup.


Confirm that you have selected the correct network interface cards for each interface on
your firewall and type “y” and press [Enter].


Once you are complete this initial setup, you will be presented with the console menu. Your firewall is now up and running. We have finished all configuration steps required to be done from the console. You can actually disconnect the monitor and keyboard from the system (as an added security precaution) for all other configuration will be done via the web console.


Open up the web browser and enter the default IP Address,,
Username: admin and Password: pfsense to get to the page as below


After successfully login to your box, you will be presented with the Status Dashboard which provides you with a summary of your system information along with the status of your interfaces installed. The dashboard is configurable and can include additional information about other components of your firewall.


From the System menu select Setup Wizard


You should then be greeted with the setup wizard, click the Next button to continue.


Complete the “General Information” section


Change to your local time zone.


WAN Interface configuration.
You need to authenticate to your ISP provider in order to access the Internet,


“Configure LAN Interface” screen


After configuring a new password, system will require your login again with the new password.
Click the Reload button to refresh the screen and login with your new password.


Now we have successfully configured the basic router setting


Make Sure to check out awesome powerful package manager


and also Network monitoring


Next time we might do Snort IDS Setup



Leave a Reply

Please log in using one of these methods to post your comment: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s